 |
Soru : panasonic uf 4100 memory clear |
| Cevap : Press Function 7 monitor key slowly 4 times * (star key) 6 scroll down to ALL JOB CLEAR set wait for the machine to initialize. |
| |
|
Soru : Canon Smartbase MPC600F WRONG CARTRIDGE |
| Cevap : Go to menu by pressing the > button , press [copy] and then # , go to 'test mode' by pressing > several times when "test mode" is on the screen press the "ok" button, now press 8 then 3 then 0, After that press the on/off button, everything should be fine now. |
| |
|
Soru : Epson HSYNC Signal Error |
| Cevap : lazer scaner birimin (laser scaner unit) degistirilmesi gereklidir. |
| |
|
Soru : Canon MFC 8440 Change Drum Soon |
| Cevap : Ön kapağı açın, CLEAR BACK tuşuna basın, sorulan soruyu YES Şeklinde cevaplayın, kapağı kapatın |
| |
|
Soru : brother ERROR 7A |
| Cevap : Main motor does not synchronize with the reference clock |
| |
|
Soru : 73 BROTHER ERROR |
| Cevap : No toner cartridge loaded |
| |
|
Soru : BROTHER CODE ERROR 71 |
| Cevap : Polygon motor does not synchronize with the reference clock |
| |
|
Soru : HP Error 50 Service |
| Cevap : 50.X FUSER ERROR alternates with For help press ? |
| |
|
Soru : Error 936 LEXMARK |
| Cevap : Error 936/937 Main Drive Motor, Transport Motor |
| |
|
Soru : Error 920 LEXMARK |
| Cevap : 920 Fuser Error Fuser is below temperature while printing. A 920 error caused by low line voltage can sometimes be cleared by turning the machine off and then on again. |
| |
|
Soru : Error 917 LEXMARK |
| Cevap : Check the transfer roll for toner buildup, surface damage to the roll, oil, or other contaminants on the surface of the roll. Replace the transfer roll as necessary. |
| |
|
Soru : Error 84 Transfer LEXMARK |
| Cevap : The Transfer drum has reached the end of it's life and must be replaced. May require service technician |
| |
|
Soru : Error 80 LEXMARK |
| Cevap : Network Card Codes These user codes are documented in various network card user manuals. See "Network Wrap Tests"€ on page 23. |
| |
|
Soru : Error 47 LEXMARK |
| Cevap : 47 Font Card Removed While Printing Printer needs data on removed card. |
| |
|
Soru : Error 44 LEXMARK |
| Cevap : Defective font card installed in font slot |
| |
|
Soru : Error 43 LEXMARK |
| Cevap : Font card format not supported by |
| |
|
Soru : Error 39 LEXMARK |
| Cevap : Page too complex to print.To verify that the printer recognizes all the installed memory, go to the user menus and print the "Print Menus"€ test page. Make sure the memory shown on the printout matches the installed memory. |
| |
|
Soru : Error 38 LEXMARK |
| Cevap : 38 Memory Full Memory used to store pages is full. To verify that the printer recognizes all the installed memory, go to the user menus and print the "Print Menus"€ test page. Make sure the memory shown on the printout matches the installed memory. |
| |
|
Soru : Error 37 LEXMARK |
| Cevap : 37 Insufficient Collation Memory Memory is too full to collate the print job. |
| |
|
Soru : Error 32 LEXMARK |
| Cevap : 32 Wrong Print Cartridge installed The installed print cartridge is not supported by the Optra printer |
| |
|
Soru : Error 31 LEXMARK |
| Cevap : Error code 31 is displayed when the top front cover is closed and a defective print cartridge is detected. It may take the printer 10-20 seconds to determine if the print cartridge is defective. Note: This error indicates the printer was able to read the cartridge ID, but the ID did not pass the verification test. |
| |
|
Soru : Error 30 LEXMARK |
| Cevap : 30 Top Cover Open or Print Cartridge Missing Make sure the spring-mounted pin on the printhead shroud is installed |
| |
|
Soru : Error 29LEXMARK |
| Cevap : The output bin sensor has not been unmade.See "Output Bin Sensor"€ on page 2-22. |
| |
|
Soru : Error 28 LEXMARK |
| Cevap : Input sensor not made after pick attempt. Tray is empty or not installed, paper jam in entry throat, or printer is requesting a manual feed. |
| |
|
Soru : Error 27 Lexmark |
| Cevap : Envelopes/paper loaded are wrong size |
| |
|
Soru : Error 26 LEXMARK |
| Cevap : Duplex unit is installed but paper tray is not sensed |
| |
|
Soru : LEXMARK ERROR CODE 25 |
| Cevap : Input sensor made at wrong time. May be due to the paper feeding manually while motors running and previous page in path. |
| |
|
Soru : Error 24 LEXMARK |
| Cevap : The defined paper size is too short to print data as formatted. |
| |
|
Soru : LEXMARK ERROR 23 |
| Cevap : Jam at the duplex unit. Paper is either not leaving the duplex entry sensor in time or not making or unmaking the duplex exit sensor in time. See "Duplex"€ on page 2-16 |
| |
|
Soru : ERROR 22 LEXMARK |
| Cevap : The exit sensor was not unmade in time |
| |
|
Soru : LEXMARK ERROR 21 |
| Cevap : The exit sensor was not made in time after the input sensor as made. |
| |
|
Soru : LEXMARK ERROR 20 |
| Cevap : Input Paper Sensor was not triggered - Paper may be jammed at the sensor. Remove toner cartridge for better access to jammed paper. |
| |
|
Soru : Error C0204 for Konica Minolta Bizhub 250 |
| Cevap : hi friends i have problem with my printer, its Konica Minolta Bizhub 250, copier and printer and scanner. |
| |
|
Soru : BizHub 162 : Error code C0500 |
| Cevap : i have one complaint for 162 when the machine is on showing c0500. i also chaged the ufr,thermisor |
| |
|
Soru : Bizhub 162 error cf032 |
| Cevap : When I turn copier on,after a few seconds,display shows error CF032,and call service.I cleaned the drum unit and waste toner,but nothing happened.Does anyone know what is the problem and how I can to reset copier.I tried to turn off copier,then I presed stop and hold and switch on,but nothing happens. |
| |
|
Soru : E6 samsung error |
| Cevap : EPROM error |
| |
|
Soru : samsung error E3 |
| Cevap : Indoor fan motor malfunction |
| |
|
Soru : samsung error E2 |
| Cevap : Indoor unit heat exchanger temperature sensor |
| |
|
Soru : samsung error E1 |
| Cevap : Indoor unit room temperature sensor error |
| |
|
Soru : xerox eror code lsu fsu |
| Cevap : lazer ünit bakım yapalım |
| |
|
Soru : samsung error code lsu |
| Cevap : lazer ünit |
| |
|
Soru : xerox 5016 E3-31 to E3-34 |
| Cevap : Exit switch jam |
| |
|
Soru : error 7980 kyocera |
| Cevap : 7980 Waste toner reservoir overflow problem |
| |
|
Soru : kyocera 1218 error |
| Cevap : F010 ROM checksum error |
| |
|
Soru : km 1500 mitaco 1218 kyocera 1218 1018 error kotları |
| Cevap : 0220 Communication problem between the main board and operation board |
| |
|
Soru : düşük ısı hatası samsung xerox |
| Cevap : fırın ünitesindeki termistör arızalı yada termistörün ucu kirlenmiş |
| |
|
Soru : cru hatası samsung 4521 |
| Cevap : yüksek sgota toner unitesinde takılı olabilir |
| |
|
Soru : konicaminolta develop cof32 hatası |
| Cevap : developer sensor kontrol hatası developer azalmış degiştirelim yada devveloper kutusuna toner ilave edelim |
| |
|
Soru : Brother MFC 4550 Error 76 |
| Cevap : Fuser ünite arıza,91i ve 99u resetle |
| |
|
Soru : KONİCAMİNOLTA C 350 C0204 |
| Cevap : TRAY 2 ELAWATOR |
| |
|
Soru : KONİCAMİNOLTA C350 C0102 HATASI |
| Cevap : LCT VERTICAL TRANSPORT MOTOR MALFUNCTİON |
| |
|
Soru : KONİCAMİNOLTA C 350 C001 HATASI |
| Cevap : LCT CONNECTİON FAİLED |
| |
|
Soru : C7410 HATASI1620 2020 2530KM 3035 KYOCERA |
| Cevap : DRUM ÜNİT |
| |
|
Soru : C3200 KM MODELLERİ HATA NEDİR |
| Cevap : SCANNER LAMP YADA KABLO OLABİLİR |
| |
|
Soru : C 6020 FİXİNG TERM.HİGH |
| Cevap : YÜKSEK ISI RESETLEYELİM 163 İŞE YARAYABİLİR KODA FGİRİŞ 10871087 |
| |
|
Soru : C4000 HATASI |
| Cevap : POLYGON MOTOR ARIZALI YADA BAKIMA IHTIYACI VAR |
| |
|
Soru : C2000 KYOCERA 2530 3035 4035 |
| Cevap : MAİN MOTOR |
| |
|
Soru : kyocera 1530 km1620 2030 2530 3035 4035 km 1500 km 116 c6000 c610 c6100 hataları |
| Cevap : yüksek ısı termistör termal fuze yada htrlamp arızalı olabilir bunlarda sorun yoksa 1087 1087 kadagirip 163 ü resetleyelim |
| |
|
Soru : brother reset |
| Cevap : menü basılı tutarak acalım 91 ve 99 reset leyelim |
| |
|
Soru : brother hl error drum lıfe reset |
| Cevap : menü düymesine parmagını basılı tut makınayı açalım..... 81 gırıp resetleyelim |
| |
|
Soru : XEROX 1012 E1 |
| Cevap : kagıt sıkışması |
| |
|
Soru : canon ır1018 koda giriş |
| Cevap : fonksiyon [# 2] 8 fonksiyon |
| |
|
Soru : canon ır1018 error e019 sistem hatası |
| Cevap : atık toner unit dolu temizle |
| |
|
Soru : samsung 4216f toner reset |
| Cevap : [menu] - [#] - 1934 - [menu] koda girişyap yeni kartuş girişini onayla |
| |
|
Soru : XEROX E1 Hata Kodu |
| Cevap : Kağıt Sıkışması |
| |
|
Soru : xerox E5 Hata Kodu |
| Cevap : Üst kapaklı açık |
| |
|
Soru : xerox E3 Hata Kodu |
| Cevap : Kağıt eritme ünitesinde sıkışmış |
| |
|
Soru : fsu hatası samsung 4521 4216f xerox pe 16 |
| Cevap : toner ünitesine yuksek sgorta takılmis olabilir yada fırın ünitesi.... |
| |
|
Soru : lsu hatasi samsung 4521f |
| Cevap : toner ünitesinin yerlestigi arka guruptaki switch kisa devre edelim düzelmiyorsa lazer ünitesine müdahale edelim |
| |
